glassdoc
01-19-2009, 08:04 PM
http://images.craigslist.org/3m23o73p51171fb12091gfb46f8d313c21680.jpghttp://images.craigslist.org/3n63k13o111512b14a91ge669e66c180b1b10.jpg
http://images.craigslist.org/3n43m73o81f114613291g0da704c31cf11f5a.jpg
LC ENGINEERING TOYOTA PROJECT - $11000 (Leesport, PA)
Reply to: see below
Date: 2009-01-16, 1:51PM EST
I have had a 93 Toyota Pickup 4x4 (short bed / green / 5 speed) in storage for the past eight years. It was in showroom condition at time of storage with 70,000 miles (no rust, no blemishes, well maintained). During this time it was striped down and rebuild as the ultimate prerunner. No expenses were spared. The project is 95% complete and I have all the necessary parts to finish. I am selling due to a major change of lifestyle and moving far away. I have well over $30,000 in parts alone. I have all receipts. Zero miles on all the BRAND NEW PARTS listed below:
- LC Engineering Custom 22R Engine with all the extras, even Dyno Testing (paid over $10,000). Bored & Stroked to 2.6L, Forged Pistons & Rods, Balanced & Blueprinted, Ported Head, Compression set for 93 octane, Oversize Valves with Dual Springs, Stage Two Cam (for low and mid range needed when in 4x4), Dual Timing Chain, Etc. Etc. Etc.
- Dual Sidedraft 40mm Weber Carbs, Intake Manifold, and K&N Filters
- New Factory Clutch
- LC Engineering Pro Distributor
- MSD Ignition and Coil
- New Radiator and hoses
- Thorley Headers and Gibson Muffler
- Marlin Crawler Transmission
- Detroit Locker in rear
- Detroit TrueTrak in front
- Ring & Pinion Gears for 31 inch tires
- New U – Joints
- Downey add a Leaf Springs in rear
- Rancho Adjustable shocks in rear
- Oversize Torsion Bars (also have stock)
- Bilstein front Shocks
- Aluminum American Racing Wheels
- 31 inch BF Goodrich Mud Terrain Tires
- Matching Spare
- Custom Aluminum Fuel Cell (paid $1,300)
- Mallory Fuel Filter, Regulator, and Guage
- S.S. Lines and Aluminum Fittings
- Smittybuilt front and rear Bumpers
- Smittybuilt Nerf Bars
- Downey Skid Plate
- Rhino Lined Bed and Tailgate in matching color
- Many other parts also lined
- Rubber Bed Mat
- Plastic Tailgate Cover
- Custom Leather Seat (paid $700)
- Autometer Gauges: Tach, Speedo, Water Temp, Oil Press, Volts, Mixture Meter, Fuel Press.
- Rebuilt Factory Brake Calibers, New Rotors and Pads
- New Drums, Shoes, and Pistons
- I have both Manual and Power Steering Gear Boxes, the Manual is currently installed.
- Many Parts Repainted and Undercoated
- Almost all bolts have been replaced with new plated hardware
- Etc. Etc. Etc.
This is definitely a truck that must be seen in person to fully appreciate the attention to detail. I am confident you can not find a cleaner truck in this area. Asking only $11,000 OBO. Must sell to move. Building this truck on your own, you would pay that much for the engine alone. I can email pics. I am located in eastern PA. Contact Brandon at 610-295-7651 or bwestenhoefer@yahoo.com
http://images.craigslist.org/3n43m73o81f114613291g0da704c31cf11f5a.jpg
LC ENGINEERING TOYOTA PROJECT - $11000 (Leesport, PA)
Reply to: see below
Date: 2009-01-16, 1:51PM EST
I have had a 93 Toyota Pickup 4x4 (short bed / green / 5 speed) in storage for the past eight years. It was in showroom condition at time of storage with 70,000 miles (no rust, no blemishes, well maintained). During this time it was striped down and rebuild as the ultimate prerunner. No expenses were spared. The project is 95% complete and I have all the necessary parts to finish. I am selling due to a major change of lifestyle and moving far away. I have well over $30,000 in parts alone. I have all receipts. Zero miles on all the BRAND NEW PARTS listed below:
- LC Engineering Custom 22R Engine with all the extras, even Dyno Testing (paid over $10,000). Bored & Stroked to 2.6L, Forged Pistons & Rods, Balanced & Blueprinted, Ported Head, Compression set for 93 octane, Oversize Valves with Dual Springs, Stage Two Cam (for low and mid range needed when in 4x4), Dual Timing Chain, Etc. Etc. Etc.
- Dual Sidedraft 40mm Weber Carbs, Intake Manifold, and K&N Filters
- New Factory Clutch
- LC Engineering Pro Distributor
- MSD Ignition and Coil
- New Radiator and hoses
- Thorley Headers and Gibson Muffler
- Marlin Crawler Transmission
- Detroit Locker in rear
- Detroit TrueTrak in front
- Ring & Pinion Gears for 31 inch tires
- New U – Joints
- Downey add a Leaf Springs in rear
- Rancho Adjustable shocks in rear
- Oversize Torsion Bars (also have stock)
- Bilstein front Shocks
- Aluminum American Racing Wheels
- 31 inch BF Goodrich Mud Terrain Tires
- Matching Spare
- Custom Aluminum Fuel Cell (paid $1,300)
- Mallory Fuel Filter, Regulator, and Guage
- S.S. Lines and Aluminum Fittings
- Smittybuilt front and rear Bumpers
- Smittybuilt Nerf Bars
- Downey Skid Plate
- Rhino Lined Bed and Tailgate in matching color
- Many other parts also lined
- Rubber Bed Mat
- Plastic Tailgate Cover
- Custom Leather Seat (paid $700)
- Autometer Gauges: Tach, Speedo, Water Temp, Oil Press, Volts, Mixture Meter, Fuel Press.
- Rebuilt Factory Brake Calibers, New Rotors and Pads
- New Drums, Shoes, and Pistons
- I have both Manual and Power Steering Gear Boxes, the Manual is currently installed.
- Many Parts Repainted and Undercoated
- Almost all bolts have been replaced with new plated hardware
- Etc. Etc. Etc.
This is definitely a truck that must be seen in person to fully appreciate the attention to detail. I am confident you can not find a cleaner truck in this area. Asking only $11,000 OBO. Must sell to move. Building this truck on your own, you would pay that much for the engine alone. I can email pics. I am located in eastern PA. Contact Brandon at 610-295-7651 or bwestenhoefer@yahoo.com